Quick answer
When choosing pipe clips for insulated pipe, size the clip to the outside diameter (OD) of the insulation block, not to the pipe. Work out the block OD as pipe OD plus twice the insulation thickness, then use the nearest standard clip size. For example, 15mm copper with 25mm insulation needs a block of about 65mm OD and a 65mm clip, not a 15mm clip.
- Block OD = pipe OD + (2 × insulation thickness), then the nearest standard clip size.
- Steel pipe is sold by nominal bore (NB), so convert it to the real OD first: 50NB steel is 60.3mm OD.
- Use the size chart below, or the free Block & Clip Selector for every size Barnvale makes.
Most clip problems on insulated jobs come from one thing: ordering the clip for the pipe. This guide explains how to choose pipe clips for insulated pipe, gives a size chart for the most common copper and steel sizes, and covers the nominal bore trap that catches out even experienced buyers.
Should a pipe clip be sized to the pipe or the insulation?
On insulated pipework the clip goes around a load-bearing insulation block, so it is sized to the block’s outside diameter. The block sits between the pipe and the clip, carries the load and keeps the insulation continuous through the support. A clip sized to the pipe will not close around the block.
Standard pipe insulation is not designed to carry a load, so every support on an insulated run should be made through a load-bearing block. On chilled water this also stops a cold bridge forming at the clip, which is where condensation, dripping and corrosion start. Our guide to choosing pipe insulation blocks compares the block materials.
How to work out the outside diameter of pipe insulation
Add the insulation thickness twice, once for each side of the pipe:
Block OD = pipe OD + (2 × insulation thickness)
Worked example: 54mm copper with 30mm insulation is 54 + (2 × 30) = 114mm. In Barnvale’s range that is a 114mm FSC® Hardwood block and a 114mm clip, or a 116mm Phenolic block, which takes the same 114mm clip.
Why the real block OD can be a few millimetres different
The formula gets you to the right clip, but the finished size of the block depends on its material:
- FSC® Hardwood and Calcium Silicate blocks, which Barnvale makes in-house, are cut so their outside diameter lands on a standard clip size. 15mm pipe with 20mm Hardwood is 54mm OD (the formula says 55mm), so it takes a standard 54mm clip.
- Phenolic blocks finish about 2mm over the formula: 15mm pipe with 25mm Phenolic is 67mm OD.
- BPS-200 Stonewool blocks generally finish at the formula size.
For Phenolic and Stonewool, Barnvale matches the nearest standard clip size, which can be a few millimetres either side of the block OD. Our team confirms every selection before supply.
Pipe clip size chart for insulated pipe
These charts come straight from Barnvale’s block and clip schedules for the most common copper and steel pipe sizes and insulation thicknesses. All sizes are in millimetres. For any other size or block material, use the Block & Clip Selector, which covers 45 pipe sizes from 15mm to 610mm OD.
FSC® Hardwood blocks: clip size
| Pipe | 20mm | 25mm | 30mm | 40mm | 50mm |
|---|---|---|---|---|---|
| 15mm copper | 54 | 65 | 76 | 95 | 114 |
| 22mm copper | 60 | 70 | 83 | 102 | 121 |
| 28mm copper | 70 | 76 | 89 | 108 | 127 |
| 35mm copper | 76 | 83 | 95 | 114 | 133 |
| 42mm copper / 32NB steel | 83 | 95 | 102 | 121 | 140 |
| 54mm copper | 95 | 102 | 114 | 133 | 152 |
| 50NB steel (60.3mm) | 102 | 108 | 121 | 140 | 159 |
| 65NB steel / 76.1mm copper | 114 | 127 | 140 | 159 | 178 |
| 80NB steel (88.9mm) | 127 | 140 | 152 | 168 | 186 |
| 100NB steel (114.3mm) | 152 | 168 | 173 | 193 | 220 |
| 125NB steel (139.7mm) | 178 | 193 | 199 | 220 | 244 |
| 150NB steel (168.3mm) | 208 | 220 | 232 | 252 | 273 |
Phenolic blocks: block OD and clip size
| Pipe | 20mm | 25mm | 30mm | 40mm | 50mm |
|---|---|---|---|---|---|
| 15mm copper | 57 → 54 | 67 → 65 | 77 → 76 | 97 → 95 | 117 → 114 |
| 22mm copper | 64 → 65 | 72 → to suit | 84 → 83 | 104 → 102 | 124 → 121 |
| 28mm copper | 70 → 70 | 80 → 83 | 90 → 89 | 110 → 108 | 130 → 127 |
| 35mm copper | 76 → 76 | 87 → 89 | 97 → 95 | 117 → 114 | 137 → 140 |
| 42mm copper / 32NB steel | 84 → 83 | 94 → 95 | 104 → 102 | 124 → 121 | 144 → 146 |
| 54mm copper | 96 → 95 | 106 → 108 | 116 → 114 | 136 → 133 | 157 → 159 |
| 50NB steel (60.3mm) | 102 → 102 | 112 → 114 | 122 → 121 | 142 → 140 | 162 → 159 |
| 65NB steel / 76.1mm copper | 118 → 121 | 128 → 127 | 138 → 140 | 158 → 159 | 178 → 178 |
| 80NB steel (88.9mm) | 131 → 133 | 141 → 140 | 151 → 152 | 171 → 168 | 191 → 193 |
| 100NB steel (114.3mm) | 156 → 152 | 166 → 168 | 176 → 178 | 196 → 193 | 216 → 220 |
| 125NB steel (139.7mm) | 182 → 186 | 192 → 193 | 202 → 199 | 222 → 220 | 242 → 244 |
| 150NB steel (168.3mm) | 210 → 208 | 220 → 220 | 230 → 232 | 250 → 252 | 270 → 273 |
The charts show the 2 bolt split band clip. “To suit” means the clip is made or confirmed to suit that block. Lightweight clips, saddles and U bolts for each size are in the Selector and on our data sheets. Copper and steel pipes with the same OD use the same block and clip.
Nominal bore vs outside diameter: copper, steel and stainless
Copper tube is sold by its actual outside diameter: 15mm copper is 15mm OD. Steel pipe is sold by nominal bore (NB, sometimes written DN), which is a reference size, not a measurement. 50NB steel pipe is 60.3mm OD, so a block or clip ordered as “50mm” will not fit it.
| Nominal bore | Steel pipe OD | Nominal bore | Steel pipe OD |
|---|---|---|---|
| 15NB | 21.3mm | 80NB | 88.9mm |
| 20NB | 26.9mm | 100NB | 114.3mm |
| 25NB | 33.7mm | 125NB | 139.7mm |
| 32NB | 42.4mm | 150NB | 168.3mm |
| 40NB | 48.3mm | 200NB | 219.1mm |
| 50NB | 60.3mm | 250NB | 273.0mm |
| 65NB | 76.1mm | 300NB | 323.9mm |
Common copper tube sizes are 15, 22, 28, 35, 42, 54, 67, 76.1 and 108mm OD.
Stainless steel catches people out because it comes both ways. Thin-wall press-fit stainless systems use copper-style OD sizes (15, 22, 28mm and so on), while heavier stainless pipe follows the nominal bore sizes above. Check which system is on the drawings before you order blocks or clips. If you are not sure, our sales team will check it with you.
Which type of clip should you use?
Once you know the block OD, choose the clip to suit the fixing:
- Split band (2 bolt) clips are the standard choice over insulation blocks. Barnvale’s split band clips to suit insulation are made to the block OD, up to 300mm nominal bore.
- Lightweight clips have a threaded M8/M10 boss for drop rod and are a quick, economical option on smaller sizes. In Barnvale’s range they suit blocks up to about 323mm OD; above that, use a split band clip.
- Saddles fix the block and pipe down to a flat surface or steelwork.
- U bolts hold the block to a steel section and suit larger pipes: Barnvale’s U bolts to suit insulation go up to 900mm nominal bore.
Rubber-lined clips are designed for bare pipe. On insulated runs the block sits between the clip and the pipe, which is why the clips in our insulated range are unlined. See the full pipe supports range.
Common mistakes when ordering pipe clips for insulated pipe
- Ordering the clip by pipe size instead of block OD.
- Adding the insulation thickness once instead of twice.
- Ordering steel blocks and clips by nominal bore instead of the actual OD.
- Mixing up stainless press-fit sizes with steel nominal bore sizes.
- Fitting a clip straight over standard insulation without a load-bearing block.
- Using a block thinner than the surrounding insulation, so the finish is not flush and the vapour barrier cannot be sealed.
Frequently asked questions
Do pipe clips go over or under the insulation?
On insulated pipework the clip goes over a load-bearing insulation block, never directly on the pipe. The insulation butts up to each side of the block and is sealed to it, so it runs continuously through the support.
Can I fit a pipe clip straight over the insulation?
No. Standard pipe insulation is not designed to carry a load, so all supports should be made through a load-bearing block. A clip tightened over ordinary insulation crushes it and can tear the vapour barrier.
Why is the block OD different from pipe OD plus twice the insulation?
FSC® Hardwood and Calcium Silicate blocks are cut so their outside diameter matches a standard clip size, and Phenolic blocks finish about 2mm over. The formula still gets you to the right clip, and the Block & Clip Selector shows the exact figures.
Is nominal bore the inside or the outside diameter?
Neither exactly. Nominal bore is a reference size. For steel pipe the outside diameter is fixed by the standard (50NB is 60.3mm OD) and the bore varies with the wall thickness, so always size blocks and clips from the OD.
What thickness of insulation do I need?
It is set by the project specification, usually following BS 5422, which gives insulation thicknesses for each service and pipe size. The block should be the same thickness as the insulation so the finish is flush and the vapour barrier can be sealed.
What is a munsen ring?
Munsen ring is a common UK name for a lightweight ring clip with a threaded boss for drop rod. For insulated pipe, size it to the block OD, the same as any other clip.
Send us your pipe schedule
Send your pipe sizes, pipe material and insulation thickness, and we will size the insulation blocks and clips and send you a quote. Barnvale makes blocks and clips in-house, so non-standard sizes can be made to suit.
